XING2 2207 2-6S FPV Motor

Our XING series NextGen motors have become popular after the initial release in 2018 and became the new standard on the market. Was it the curved shape or the internal damping ring to protect the bearing, or was it the higher quality NSK bearings coupled with a higher grade titanium alloy shaft? We've been copied and compared all these years, but now it's time to set a new standard again! We're finally ready to announce our predecessor the XING2!

The smooth, reliable and powerful XING motors were upgraded and we achieved an even higher standard in our manufactory as well as better performance than ever before. New center slotted N52H curved arc magnets were introduced to drastically reduce response time of the motor! Maybe the biggest bottleneck of our FPV flight controller is the motor due to it's translation delay of it braking and accelerating. XING2 motors offer faster response to translate your PID loop quicker and get that locked-in feeling you were always looking for!

Due to the high quality materials used and the durable joint of bell and shaft, we were able to reduce the magnet air gap and stator lamination to a minimum. The smaller the air gap is, the lower that reluctance and the higher the magnetic flux (which is the magnetic analog of current) causing more efficiency and higher power!

UART1 for VTX HD/Analog

UART2 for  Receiver

UART4 for GPS

UART5 for ESC Telemetry

8×Dshot/PWM outputs 

2×I2C  for GPS Mag

Our XING series NextGen motors have become popular after the initial release in 2018 and became the new standard on the market. Was it the curved shape or the internal damping ring to protect the bearing, or was it the higher quality NSK bearings coupled with a higher grade titanium alloy shaft? We've been copied and compared all these years, but now it's time to set a new standard again! We're finally ready to announce our predecessor the XING2!

The smooth, reliable and powerful XING motors were upgraded and we achieved an even higher standard in our manufactory as well as better performance than ever before. New center slotted N52H curved arc magnets were introduced to drastically reduce response time of the motor! Maybe the biggest bottleneck of our FPV flight controller is the motor due to it's translation delay of it braking and accelerating. XING2 motors offer faster response to translate your PID loop quicker and get that locked-in feeling you were always looking for!

Due to the high quality materials used and the durable joint of bell and shaft, we were able to reduce the magnet air gap and stator lamination to a minimum. The smaller the air gap is, the lower that reluctance and the higher the magnetic flux (which is the magnetic analog of current) causing more efficiency and higher power!

Oct. 26, 2024: The screws specification in Packing is updated from M3*7 screws to M3*10mm.

The MOSFET used by BLITZ E80 is PSMN1R0-40YLD, which can withstand a continuous current of 80A at 25°C, with a maximum power dissipation of 198W. BEC power supply adopts TI automotive-grade dedicated synchronous rectifier chip, supporting up to 100V.

The 1-4 layer power board of the PCB circuit is ultra-thick copper with a thickness of 4OZ, ensuring continuous output under high-power operation. The STM32F051 main control processor with a running frequency of up to 48MHz, combined with a three-in-one driver IC, achieves a faster running speed!

Oct. 26, 2024: The screws specification in Packing is updated from M3*7 screws to M3*10mm.

5mm titanium alloy shaft, our strongest prop shaft ever!

Crash resistant 7075 aluminum bell

Smooth and long-lasting NSK 9x4x4 bearings

Center slotted N52H curved arc magnets

XING O-ring bearing gap protection

Motor wires protector

Dynamically balanced

Rational layout, countersunk holes on extended solder pads to ensure PCB layer connection

G071 MCU, 48mHz maximum clock speed;

TDK MLCC Low ESR ceramic capacitors;

Top grade PSMN1R0-40YLD MOSFET;

8 layers double-sided PCB board

5mm titanium alloy shaft, our strongest prop shaft ever!

Crash resistant 7075 aluminum bell

Smooth and long-lasting NSK 9x4x4 bearings

Center slotted N52H curved arc magnets

XING O-ring bearing gap protection

Motor wires protector

Dynamically balanced

KV: 1750KV / 2750KV / 2050KV

Weight(included wire): 30.5g

Dimension: φ29*32.25mm

Interphase Resistance: 74.23mΩ(1750KV/2750KV) / 56.3mmΩ(2050KV)

Input Volts: 25.2V (1750KV/2050KV) / 16.8V (2750KV)

Peak Current: 36.03A(1750KV)/ 46.05A (2750KV)/ 49.53A(2750KV)

Max Watt: 898W(1750KV) / 706.9W(2750KV) / 1166.4W(2750KV)

Mounting Holes: 16*16 φ3mm

Rotor Specifications: Unibell

Shaft Diameter: 5mm

Shaft Protruding Length: 13.5mm

Lead: 160mm/20AWG

Magnet: N52H Curved

Configuration: 12N14P

Bearing Type: NSK

Bearing Specification: φ9*φ4*4

Winding: Single Strand copper winding

Product Name: BLITZ E80 4-IN-1 ESC

Input Voltage: 2-8S

Max. Continuous Current: 80A

Max. Burst Current: 100A

MCU: G071

BEC: No

Firmware: BLHeli32

Current Sensor: Yes

Telemetry: Supported

Target: IFLIGHT_BLITZ_G2

Mounting Dimensions: 35x35mm/Φ3mm

Dimensions: 35x42mm

Weight: 65g(±10)

Protocal:Supports DShot DShot150/300/600/MultiShot/ OneShot etc

KV: 1750KV / 2750KV / 2050KV

Weight(included wire): 30.5g

Dimension: φ29*32.25mm

Interphase Resistance: 74.23mΩ(1750KV/2750KV) / 56.3mmΩ(2050KV)

Input Volts: 25.2V (1750KV/2050KV) / 16.8V (2750KV)

Peak Current: 36.03A(1750KV)/ 46.05A (2750KV)/ 49.53A(2750KV)

Max Watt: 898W(1750KV) / 706.9W(2750KV) / 1166.4W(2750KV)

Mounting Holes: 16*16 φ3mm

Rotor Specifications: Unibell

Shaft Diameter: 5mm

Shaft Protruding Length: 13.5mm

Lead: 160mm/20AWG

Magnet: N52H Curved

Configuration: 12N14P

Bearing Type: NSK

Bearing Specification: φ9*φ4*4

Winding: Single Strand copper winding

1 x XING2 2207 Black Brushless Motor 

4 x M3*10 screws (1750KV)

4 x M3*7 screws(2750KV)

4 x M3*9 screws (2050KV)

1 x M5 Flanged Nylon Insert Lock Nut

1 x BLITZ H7 Pro Flight Controller

1 x BLITZ E80 4-IN-1 ESC (Combo1)

2 x BLITZ E80 4-IN-1 ESC (Combo2)

1 x 50V 470UF capacitor Plate

2 x 50V 1000UF capacitor

1 x Wiring set

1 x USB Adapter Board

1 x XING2 2207 Black Brushless Motor 

4 x M3*10 screws (1750KV)

4 x M3*7 screws(2750KV)

4 x M3*9 screws (2050KV)

1 x M5 Flanged Nylon Insert Lock Nut